Schärfentiefe-Rechner

Mit dem Schärfentiefe-Rechner schätzen Sie die Nah- und Fernpunkte der Schärfe, die gesamte Schärfentiefe und die hyperfokale Distanz für jede Kombination aus Brennweite, Blende, Sensorformat und Motivabstand ab. Der Rechner ist für die alltägliche Studio- und Produktfotografie mit Vollformat- und Canon APS-C-Kameras gedacht und unterstützt metrische und imperiale Einheiten.

PhotoRobot Schärfentiefe-Rechner

Schätzen Sie Nah- und Fernpunkt der Schärfe, die gesamte Schärfentiefe und die hyperfokale Distanz ab.

Einstellungen

mm

Der Schieberegler deckt den typischen Studiobereich ab (16–300 mm). Für Weitwinkel- oder Teleobjektive mit anderen Brennweiten geben Sie im Feld oben einen beliebigen Wert (4–1200 mm) ein.

Blende f/16
cm
Distance measured from

Measured from the focal-plane mark ⦵ on the camera body, the same reference lens specs use for minimum focus distance. The calculator converts it to the lens-to-subject distance (thin-lens equation), and near/far limits are shown from the sensor mark too. See the diagram.

mm

Only to show the distance from the front of the lens; it does not change the DoF. Canon RF: 20 mm flange + lens length from the spec sheet (EF: 44 mm). Zoom lenses get longer as you zoom.

Ergebnisse

Gesamte Schärfentiefe
34 cm
Near limit 86 cm
Far limit 120 cm
In front of subject 14 cm
Behind subject 20 cm
Hyperfocal distance 531 cm
Lens to subject (used in formula) 95 cm
Zerstreuungskreis 0,030 mm

Standardmodell der Schärfentiefe für dünne Linsen: H = f²/(N·c) + f. Die Werte können aufgrund von Beugung, Focus Breathing und der individuellen Objektivkonstruktion geringfügig von realen Objektiven abweichen.

Lens or sensor mark: where do you measure subject distance from?
Two ways to measure subject distance Side view of a camera, lens and product. The orange dimension runs from the focal-plane mark on the camera body, which marks the sensor, to the subject (S). The black dimension runs from the lens's optical center to the subject (u). The gap between sensor and optical center is v, so S equals u plus v. sensor optical center subject S · from the sensor mark v front of lens u · from the lens

Sensor mark (S). The ⦵ symbol on the top of the camera body marks the sensor plane. Lens specifications measure the minimum focus distance from it, and it is the easiest point to measure from on a PhotoRobot setup with a tape.

Lens (u). Depth of field formulas need the distance from the lens's optical center to the subject. When you pick Sensor mark, the calculator splits S into u + v with the thin-lens equation 1/u + 1/v = 1/f: u = S/2 · (1 + √(1 − 4f/S)). Near and far limits and the hyperfocal distance are then shown from the sensor mark as well.

The difference matters at product distances: a 105 mm lens at f/16 with the sensor mark 918 mm from the subject gives 4.8 cm of depth of field. Entering the same 918 mm as a distance from the lens would show 6.5 cm, about a third too much.

The conversion assumes a thin lens. Real lenses focus internally and their optical center is not exactly where the diagram shows it, so treat results close to the minimum focus distance (macro) as estimates. A thin lens cannot focus closer than 4 × the focal length from the sensor (1:1). If you measured from the front of the lens, add the sensor mark to front of lens length to get S.

Was ist die hyperfokale Distanz – und warum ist sie für die Studioarbeit wichtig?

Die hyperfokale Distanz (H) ist die kürzeste Entfernung, auf die ein Objektiv fokussiert werden kann, wobei Objekte im Unendlichen noch akzeptabel scharf abgebildet werden. Fokussieren Sie genau auf H, reicht die Schärfentiefe von H/2 bis ∞ – der Kniff, mit dem Landschaftsfotografen Vordergrund und Horizont gleichzeitig scharf halten.

In der Studio- und Produktfotografie dient er meist nur als Richtwert: Solange Ihre Motiventfernung deutlich kleiner als H ist (was in der Regel der Fall ist – H wächst mit dem Quadrat der Brennweite und sinkt nur mit der Blende), bleibt die Schärfentiefe annähernd symmetrisch um das Motiv verteilt. Nähert sich die Motiventfernung H, reicht die Fernpunktgrenze bis ins Unendliche, und der Rechner zeigt ∞ an.

Praktischer Tipp für die Produkt- und Schmuckfotografie: Fokussieren Sie auf das am weitesten vorn liegende Detail, das scharf sein soll, und prüfen Sie anhand der Zeilen „Near limit“ / „Far limit“ oben (oder anhand des Schärfentiefe-Diagramms), ob der Rest des Objekts innerhalb der Schärfentiefe liegt.

Weitere Ressourcen zur Schärfentiefe

Weitere Ressourcen zur Berechnung der Schärfentiefe für PhotoRobot-Kunden finden Sie in den folgenden Benutzerhandbüchern. Sie enthalten Informationen zur Schärfentiefe im Zusammenhang mit den von PhotoRobot empfohlenen Kameras, zur Kameraauflösung und zur PhotoRobot-Studiobeleuchtung.