Kalkulator globinske ostrine

S kalkulatorjem globinske ostrine ocenite bližnjo in oddaljeno mejo ostrine, skupno globinsko ostrino ter hiperfokalno razdaljo za poljubno kombinacijo goriščne razdalje, zaslonke, formata senzorja in razdalje do motiva. Kalkulator je namenjen vsakodnevni studijski in produktni fotografiji s fotoaparati s polnim formatom in Canon APS-C ter podpira metrične in imperialne enote.

Kalkulator globinske ostrine PhotoRobot

Ocenite bližnjo in oddaljeno mejo ostrine, skupno globinsko ostrino in hiperfokalno razdaljo.

Nastavitve

mm

Drsnik zajema običajno studijsko območje (16–300 mm). Za širokokotne ali daljše objektive vnesite poljubno vrednost (4–1200 mm) v polje zgoraj.

Zaslonka f/16
cm
Distance measured from

Measured from the focal-plane mark ⦵ on the camera body, the same reference lens specs use for minimum focus distance. The calculator converts it to the lens-to-subject distance (thin-lens equation), and near/far limits are shown from the sensor mark too. See the diagram.

mm

Only to show the distance from the front of the lens; it does not change the DoF. Canon RF: 20 mm flange + lens length from the spec sheet (EF: 44 mm). Zoom lenses get longer as you zoom.

Rezultati

Skupna globinska ostrina
34 cm
Near limit 86 cm
Far limit 120 cm
In front of subject 14 cm
Behind subject 20 cm
Hyperfocal distance 531 cm
Lens to subject (used in formula) 95 cm
Krožec konfuzije 0,030 mm

Standardni model globinske ostrine za tanko lečo: H = f²/(N·c) + f. Vrednosti se zaradi uklona svetlobe, spreminjanja goriščne razdalje pri ostrenju (focus breathing) in zasnove posameznega objektiva lahko nekoliko razlikujejo od vrednosti pri dejanskih objektivih.

Lens or sensor mark: where do you measure subject distance from?
Two ways to measure subject distance Side view of a camera, lens and product. The orange dimension runs from the focal-plane mark on the camera body, which marks the sensor, to the subject (S). The black dimension runs from the lens's optical center to the subject (u). The gap between sensor and optical center is v, so S equals u plus v. sensor optical center subject S · from the sensor mark v front of lens u · from the lens

Sensor mark (S). The ⦵ symbol on the top of the camera body marks the sensor plane. Lens specifications measure the minimum focus distance from it, and it is the easiest point to measure from on a PhotoRobot setup with a tape.

Lens (u). Depth of field formulas need the distance from the lens's optical center to the subject. When you pick Sensor mark, the calculator splits S into u + v with the thin-lens equation 1/u + 1/v = 1/f: u = S/2 · (1 + √(1 − 4f/S)). Near and far limits and the hyperfocal distance are then shown from the sensor mark as well.

The difference matters at product distances: a 105 mm lens at f/16 with the sensor mark 918 mm from the subject gives 4.8 cm of depth of field. Entering the same 918 mm as a distance from the lens would show 6.5 cm, about a third too much.

The conversion assumes a thin lens. Real lenses focus internally and their optical center is not exactly where the diagram shows it, so treat results close to the minimum focus distance (macro) as estimates. A thin lens cannot focus closer than 4 × the focal length from the sensor (1:1). If you measured from the front of the lens, add the sensor mark to front of lens length to get S.

Kaj je hiperfokalna razdalja in zakaj je pomembna pri studijskem delu?

Hiperfokalna razdalja (H) je najmanjša razdalja, na katero lahko izostrite objektiv, da so predmeti v neskončnosti še sprejemljivo ostri. Če izostrite natančno na H, se globinska ostrina razteza od H/2 vse do ∞ – trik, ki ga pri krajinski fotografiji uporabljajo za ostrino v ospredju in na obzorju.

Pri studijskem in produktnem fotografiranju gre večinoma za kazalnik: dokler je razdalja do motiva precej manjša od H (kar običajno drži – H narašča s kvadratom goriščne razdalje in se manjša le z zaslonko), je globinska ostrina okoli motiva približno simetrična. Ko se razdalja do motiva približa vrednosti H, se zadnja meja razteguje v neskončnost in kalkulator prikaže ∞.

Praktičen nasvet za fotografiranje izdelkov in nakita: izostrite na najbolj sprednji detajl, ki mora biti oster, ter s vrsticama „Near limit“ / „Far limit“ zgoraj (ali s tabelo globinske ostrine) preverite, ali preostanek predmeta sodi v območje globinske ostrine.

Dodatni viri o globinski ostrini

Dodatne vire o izračunu globinske ostrine za stranke podjetja PhotoRobot najdete v naslednjih uporabniških priročnikih. Vsebujejo informacije o globinski ostrini glede na kamere, ki jih priporoča PhotoRobot, o razumevanju ločljivosti kamere ter o studijski osvetlitvi PhotoRobot.