Kalkulator dubinske oštrine

Pomoću kalkulatora dubinske oštrine procijenite bližu i dalju granicu fokusa, ukupnu dubinsku oštrinu i hiperfokalnu udaljenost za bilo koju kombinaciju žarišne daljine, otvora blende, formata senzora i udaljenosti objekta. Kalkulator je namijenjen svakodnevnoj studijskoj fotografiji i fotografiji proizvoda s full-frame i Canon APS-C fotoaparatima, uz metričke i imperijalne jedinice.

PhotoRobot kalkulator dubinske oštrine

Procijenite bližu i dalju granicu fokusa, ukupnu DoF i hiperfokalnu udaljenost.

Postavke

mm

Klizač pokriva uobičajeni studijski raspon (16–300 mm). Za šire ili duže objektive unesite bilo koju vrijednost (4–1200 mm) u polje iznad.

Otvor blende f/16
cm
Distance measured from

Measured from the focal-plane mark ⦵ on the camera body, the same reference lens specs use for minimum focus distance. The calculator converts it to the lens-to-subject distance (thin-lens equation), and near/far limits are shown from the sensor mark too. See the diagram.

mm

Only to show the distance from the front of the lens; it does not change the DoF. Canon RF: 20 mm flange + lens length from the spec sheet (EF: 44 mm). Zoom lenses get longer as you zoom.

Rezultati

Ukupna dubinska oštrina
34 cm
Near limit 86 cm
Far limit 120 cm
In front of subject 14 cm
Behind subject 20 cm
Hyperfocal distance 531 cm
Lens to subject (used in formula) 95 cm
Krug konfuzije 0,030 mm

Standardni DoF model tankog objektiva: H = f²/(N·c) + f. Vrijednosti se mogu neznatno razlikovati od stvarnih objektiva zbog difrakcije, promjene vidnog polja pri fokusiranju (focus breathing) i konstrukcije pojedinačnog objektiva.

Lens or sensor mark: where do you measure subject distance from?
Two ways to measure subject distance Side view of a camera, lens and product. The orange dimension runs from the focal-plane mark on the camera body, which marks the sensor, to the subject (S). The black dimension runs from the lens's optical center to the subject (u). The gap between sensor and optical center is v, so S equals u plus v. sensor optical center subject S · from the sensor mark v front of lens u · from the lens

Sensor mark (S). The ⦵ symbol on the top of the camera body marks the sensor plane. Lens specifications measure the minimum focus distance from it, and it is the easiest point to measure from on a PhotoRobot setup with a tape.

Lens (u). Depth of field formulas need the distance from the lens's optical center to the subject. When you pick Sensor mark, the calculator splits S into u + v with the thin-lens equation 1/u + 1/v = 1/f: u = S/2 · (1 + √(1 − 4f/S)). Near and far limits and the hyperfocal distance are then shown from the sensor mark as well.

The difference matters at product distances: a 105 mm lens at f/16 with the sensor mark 918 mm from the subject gives 4.8 cm of depth of field. Entering the same 918 mm as a distance from the lens would show 6.5 cm, about a third too much.

The conversion assumes a thin lens. Real lenses focus internally and their optical center is not exactly where the diagram shows it, so treat results close to the minimum focus distance (macro) as estimates. A thin lens cannot focus closer than 4 × the focal length from the sensor (1:1). If you measured from the front of the lens, add the sensor mark to front of lens length to get S.

Šta je hiperfokalna udaljenost i zašto je važna u studijskom radu?

Hiperfokalna udaljenost (H) je najmanja udaljenost na koju se objektiv može fokusirati, a da objekti u beskonačnosti ostanu prihvatljivo oštri. Ako fokusirate tačno na H, dubinska oštrina se proteže od H/2 sve do ∞ – trik koji pejzažni fotografi koriste kako bi i prednji plan i horizont bili oštri.

U studijskoj fotografiji i fotografiji proizvoda to je uglavnom samo indikator: sve dok je udaljenost objekta znatno manja od H (što je obično slučaj — H raste s kvadratom žižne daljine, a smanjuje se samo s otvorom blende), dubinska oštrina (DoF) ostaje približno simetrična oko objekta. Kada se udaljenost objekta približi vrijednosti H, daleka granica odlazi u beskonačnost, a kalkulator će prikazati ∞.

Praktičan savjet za rad s proizvodima i nakitom: fokusirajte se na prvi detalj u prednjem planu koji mora biti oštar, a zatim pomoću redova „Near limit“ / „Far limit“ iznad (ili tabele dubinske oštrine) provjerite stane li ostatak objekta unutar DoF-a.

Dodatni resursi o dubinskoj oštrini

Dodatne resurse o izračunu dubinske oštrine za korisnike sistema PhotoRobot možete pronaći u sljedećim korisničkim priručnicima. Pronaći ćete informacije o dubinskoj oštrini u vezi s kamerama koje preporučuje PhotoRobot, o razumijevanju rezolucije kamere te o PhotoRobot studijskoj rasvjeti.