Alan Derinliği Hesaplayıcı

Odak uzaklığı, diyafram, sensör formatı ve özne mesafesinin herhangi bir kombinasyonu için yakın ve uzak netlik sınırlarını, toplam alan derinliğini ve hiperfokal mesafeyi tahmin etmek üzere Alan Derinliği Hesaplayıcı’yı kullanın. Hesaplayıcı, tam kare ve Canon APS-C kameralarla gündelik stüdyo ve ürün fotoğrafçılığı için tasarlanmıştır ve metrik ile imperial birimleri destekler.

PhotoRobot Alan Derinliği Hesaplayıcı

Yakın ve uzak netlik sınırlarını, toplam DoF’u ve hiperfokal mesafeyi tahmin edin.

Ayarlar

mm

Kaydırıcı, tipik stüdyo aralığını (16–300 mm) kapsar. Daha geniş açılı veya daha uzun lensler için yukarıdaki alana herhangi bir değer (4–1200 mm) girebilirsiniz.

Diyafram f/16
cm
Distance measured from

Measured from the focal-plane mark ⦵ on the camera body, the same reference lens specs use for minimum focus distance. The calculator converts it to the lens-to-subject distance (thin-lens equation), and near/far limits are shown from the sensor mark too. See the diagram.

mm

Only to show the distance from the front of the lens; it does not change the DoF. Canon RF: 20 mm flange + lens length from the spec sheet (EF: 44 mm). Zoom lenses get longer as you zoom.

Sonuçlar

Toplam alan derinliği
34 cm
Near limit 86 cm
Far limit 120 cm
In front of subject 14 cm
Behind subject 20 cm
Hyperfocal distance 531 cm
Lens to subject (used in formula) 95 cm
Karışıklık çemberi 0,030 mm

Standart ince mercek DoF modeli: H = f²/(N·c) + f. Kırınım, odak solunumu (focus breathing) ve lense özgü tasarım nedeniyle değerler gerçek lenslerden hafifçe farklılık gösterebilir.

Lens or sensor mark: where do you measure subject distance from?
Two ways to measure subject distance Side view of a camera, lens and product. The orange dimension runs from the focal-plane mark on the camera body, which marks the sensor, to the subject (S). The black dimension runs from the lens's optical center to the subject (u). The gap between sensor and optical center is v, so S equals u plus v. sensor optical center subject S · from the sensor mark v front of lens u · from the lens

Sensor mark (S). The ⦵ symbol on the top of the camera body marks the sensor plane. Lens specifications measure the minimum focus distance from it, and it is the easiest point to measure from on a PhotoRobot setup with a tape.

Lens (u). Depth of field formulas need the distance from the lens's optical center to the subject. When you pick Sensor mark, the calculator splits S into u + v with the thin-lens equation 1/u + 1/v = 1/f: u = S/2 · (1 + √(1 − 4f/S)). Near and far limits and the hyperfocal distance are then shown from the sensor mark as well.

The difference matters at product distances: a 105 mm lens at f/16 with the sensor mark 918 mm from the subject gives 4.8 cm of depth of field. Entering the same 918 mm as a distance from the lens would show 6.5 cm, about a third too much.

The conversion assumes a thin lens. Real lenses focus internally and their optical center is not exactly where the diagram shows it, so treat results close to the minimum focus distance (macro) as estimates. A thin lens cannot focus closer than 4 × the focal length from the sensor (1:1). If you measured from the front of the lens, add the sensor mark to front of lens length to get S.

Hiperfokal mesafe nedir ve stüdyo çalışmaları için neden önemlidir?

Hiperfokal mesafe (H), bir lensin odaklanabileceği ve sonsuzdaki nesneleri hâlâ kabul edilebilir netlikte tutan en yakın mesafedir. Tam olarak H mesafesine odaklandığınızda alan derinliği H/2 noktasından ∞ noktasına kadar uzanır; manzara fotoğrafçılarının hem ön planı hem de ufku net tutmak için kullandığı yöntem budur.

Stüdyo ve ürün fotoğrafçılığında bu değer çoğunlukla bir gösterge niteliğindedir: Konu mesafeniz H değerinden çok daha küçük olduğu sürece (genellikle böyledir; H, odak uzaklığının karesiyle artar ve yalnızca diyaframla azalır) alan derinliği konunun etrafında yaklaşık simetrik kalır. Konu mesafesi H değerine yaklaştığında uzak sınır sonsuza uzanır ve hesaplayıcı ∞ değerini gösterir.

Ürün/mücevher çekimleri için pratik çıkarım: Net olmasını istediğiniz en öndeki ayrıntıya odaklanın ve nesnenin geri kalanının alan derinliği içinde kaldığını doğrulamak için yukarıdaki “Near limit” / “Far limit” satırlarını (veya Alan Derinliği Tablosunu) kullanın.

Alan Derinliği ile İlgili Ek Kaynaklar

PhotoRobot müşterileri için alan derinliği hesaplamasına dair ek kaynaklara aşağıdaki kullanım kılavuzlarından ulaşabilirsiniz. Kılavuzlarda PhotoRobot'un önerdiği kameralar, kamera çözünürlüğünün anlaşılması ve PhotoRobot stüdyo aydınlatması açısından alan derinliği hakkında bilgi bulabilirsiniz.