Calcolatore della profondità di campo

Utilizzi il calcolatore della profondità di campo per stimare i limiti di messa a fuoco anteriore e posteriore, la profondità di campo totale e la distanza iperfocale per qualsiasi combinazione di lunghezza focale, apertura, formato del sensore e distanza del soggetto. Il calcolatore è pensato per la fotografia in studio e di prodotto di uso quotidiano con fotocamere full-frame e Canon APS-C, con unità di misura metriche e imperiali.

Calcolatore della profondità di campo PhotoRobot

Stimi i limiti di messa a fuoco anteriore e posteriore, la profondità di campo totale e la distanza iperfocale.

Impostazioni

mm

Il cursore copre la gamma tipica da studio (16–300 mm). Per obiettivi più grandangolari o più lunghi, inserisca un valore qualsiasi (4–1200 mm) nel campo sopra.

Apertura f/16
cm
Distance measured from

Measured from the focal-plane mark ⦵ on the camera body, the same reference lens specs use for minimum focus distance. The calculator converts it to the lens-to-subject distance (thin-lens equation), and near/far limits are shown from the sensor mark too. See the diagram.

mm

Only to show the distance from the front of the lens; it does not change the DoF. Canon RF: 20 mm flange + lens length from the spec sheet (EF: 44 mm). Zoom lenses get longer as you zoom.

Risultati

Profondità di campo totale
34 cm
Near limit 86 cm
Far limit 120 cm
In front of subject 14 cm
Behind subject 20 cm
Hyperfocal distance 531 cm
Lens to subject (used in formula) 95 cm
Cerchio di confusione 0,030 mm

Modello standard di profondità di campo a lente sottile: H = f²/(N·c) + f. I valori possono differire leggermente dagli obiettivi reali a causa di diffrazione, focus breathing e caratteristiche progettuali del singolo obiettivo.

Lens or sensor mark: where do you measure subject distance from?
Two ways to measure subject distance Side view of a camera, lens and product. The orange dimension runs from the focal-plane mark on the camera body, which marks the sensor, to the subject (S). The black dimension runs from the lens's optical center to the subject (u). The gap between sensor and optical center is v, so S equals u plus v. sensor optical center subject S · from the sensor mark v front of lens u · from the lens

Sensor mark (S). The ⦵ symbol on the top of the camera body marks the sensor plane. Lens specifications measure the minimum focus distance from it, and it is the easiest point to measure from on a PhotoRobot setup with a tape.

Lens (u). Depth of field formulas need the distance from the lens's optical center to the subject. When you pick Sensor mark, the calculator splits S into u + v with the thin-lens equation 1/u + 1/v = 1/f: u = S/2 · (1 + √(1 − 4f/S)). Near and far limits and the hyperfocal distance are then shown from the sensor mark as well.

The difference matters at product distances: a 105 mm lens at f/16 with the sensor mark 918 mm from the subject gives 4.8 cm of depth of field. Entering the same 918 mm as a distance from the lens would show 6.5 cm, about a third too much.

The conversion assumes a thin lens. Real lenses focus internally and their optical center is not exactly where the diagram shows it, so treat results close to the minimum focus distance (macro) as estimates. A thin lens cannot focus closer than 4 × the focal length from the sensor (1:1). If you measured from the front of the lens, add the sensor mark to front of lens length to get S.

Che cos'è la distanza iperfocale e perché è importante nel lavoro in studio?

La distanza iperfocale (H) è la distanza minima alla quale è possibile mettere a fuoco un obiettivo mantenendo comunque accettabilmente nitidi gli oggetti all'infinito. Mettendo a fuoco esattamente su H, la profondità di campo si estende da H/2 fino a ∞: il metodo usato dai fotografi di paesaggio per mantenere nitidi sia il primo piano sia l'orizzonte.

Nella fotografia in studio e di prodotto H è soprattutto un indicatore: finché la distanza del soggetto è molto inferiore a H (come avviene di solito, poiché H cresce con il quadrato della lunghezza focale e diminuisce solo con l'apertura), la profondità di campo resta pressoché simmetrica attorno al soggetto. Quando la distanza del soggetto si avvicina a H, il limite lontano si estende all'infinito e il calcolatore mostrerà ∞.

Indicazione pratica per i lavori su prodotti e gioielli: metta a fuoco il dettaglio più vicino che deve risultare nitido e utilizzi le righe «Near limit» / «Far limit» qui sopra (oppure la tabella della profondità di campo) per verificare che il resto dell'oggetto rientri nella profondità di campo.

Ulteriori risorse sulla profondità di campo

Per ulteriori risorse sul calcolo della profondità di campo dedicate ai clienti PhotoRobot, consulti i manuali d'uso seguenti. Vi troverà informazioni sulla profondità di campo in relazione alle fotocamere consigliate da PhotoRobot, sulla risoluzione delle fotocamere e sull'illuminazione dello studio PhotoRobot.