Kalkulator głębi ostrości

Kalkulator głębi ostrości pozwala oszacować bliską i daleką granicę ostrości, całkowitą głębię ostrości oraz odległość hiperfokalną dla dowolnej kombinacji ogniskowej, przysłony, formatu matrycy i odległości od obiektu. Narzędzie jest przeznaczone do codziennej pracy w fotografii studyjnej i produktowej z aparatami pełnoklatkowymi oraz Canon APS-C, z jednostkami metrycznymi i imperialnymi.

Kalkulator głębi ostrości PhotoRobot

Szacowanie bliskiej i dalekiej granicy ostrości, całkowitej głębi ostrości oraz odległości hiperfokalnej.

Ustawienia

mm

Suwak obejmuje typowy zakres studyjny (16–300 mm). W przypadku szerszych lub dłuższych obiektywów dowolną wartość (4–1200 mm) można wpisać w polu powyżej.

Przysłona f/16
cm
Distance measured from

Measured from the focal-plane mark ⦵ on the camera body, the same reference lens specs use for minimum focus distance. The calculator converts it to the lens-to-subject distance (thin-lens equation), and near/far limits are shown from the sensor mark too. See the diagram.

mm

Only to show the distance from the front of the lens; it does not change the DoF. Canon RF: 20 mm flange + lens length from the spec sheet (EF: 44 mm). Zoom lenses get longer as you zoom.

Wyniki

Całkowita głębia ostrości
34 cm
Near limit 86 cm
Far limit 120 cm
In front of subject 14 cm
Behind subject 20 cm
Hyperfocal distance 531 cm
Lens to subject (used in formula) 95 cm
Krążek rozproszenia 0,030 mm

Standardowy model głębi ostrości dla cienkiej soczewki: H = f²/(N·c) + f. Wartości mogą nieznacznie odbiegać od rzeczywistych obiektywów z powodu dyfrakcji, zmiany ogniskowej przy ustawianiu ostrości (focus breathing) oraz indywidualnej konstrukcji obiektywu.

Lens or sensor mark: where do you measure subject distance from?
Two ways to measure subject distance Side view of a camera, lens and product. The orange dimension runs from the focal-plane mark on the camera body, which marks the sensor, to the subject (S). The black dimension runs from the lens's optical center to the subject (u). The gap between sensor and optical center is v, so S equals u plus v. sensor optical center subject S · from the sensor mark v front of lens u · from the lens

Sensor mark (S). The ⦵ symbol on the top of the camera body marks the sensor plane. Lens specifications measure the minimum focus distance from it, and it is the easiest point to measure from on a PhotoRobot setup with a tape.

Lens (u). Depth of field formulas need the distance from the lens's optical center to the subject. When you pick Sensor mark, the calculator splits S into u + v with the thin-lens equation 1/u + 1/v = 1/f: u = S/2 · (1 + √(1 − 4f/S)). Near and far limits and the hyperfocal distance are then shown from the sensor mark as well.

The difference matters at product distances: a 105 mm lens at f/16 with the sensor mark 918 mm from the subject gives 4.8 cm of depth of field. Entering the same 918 mm as a distance from the lens would show 6.5 cm, about a third too much.

The conversion assumes a thin lens. Real lenses focus internally and their optical center is not exactly where the diagram shows it, so treat results close to the minimum focus distance (macro) as estimates. A thin lens cannot focus closer than 4 × the focal length from the sensor (1:1). If you measured from the front of the lens, add the sensor mark to front of lens length to get S.

Czym jest odległość hiperfokalna i dlaczego ma znaczenie w pracy studyjnej?

Odległość hiperfokalna (H) to najmniejsza odległość, na którą można ustawić ostrość obiektywu, tak aby obiekty w nieskończoności pozostały akceptowalnie ostre. Po ustawieniu ostrości dokładnie na H głębia ostrości rozciąga się od H/2 aż do ∞ – z tej metody korzystają fotografowie krajobrazu, aby zachować ostrość zarówno na pierwszym planie, jak i na horyzoncie.

W fotografii studyjnej i produktowej jest to głównie wskaźnik orientacyjny: dopóki odległość od obiektu jest znacznie mniejsza niż H (a zwykle tak jest — H rośnie z kwadratem ogniskowej i maleje wyłącznie wraz z przysłoną), głębia ostrości rozkłada się wokół obiektu mniej więcej symetrycznie. Gdy odległość od obiektu zbliża się do H, granica daleka biegnie do nieskończoności, a kalkulator wyświetli ∞.

Praktyczna wskazówka dla fotografii produktowej i jubilerskiej: proszę ustawić ostrość na najbliższy szczegół, który ma być ostry, a następnie sprawdzić w wierszach „Near limit” / „Far limit” powyżej (lub na wykresie głębi ostrości), czy reszta obiektu mieści się w zakresie głębi ostrości.

Dodatkowe materiały o głębi ostrości

Dodatkowe materiały dotyczące obliczania głębi ostrości dla klientów PhotoRobot znajdą Państwo w poniższych instrukcjach obsługi. Opisują one głębię ostrości w odniesieniu do aparatów zalecanych przez PhotoRobot, rozdzielczość aparatu oraz oświetlenie studyjne PhotoRobot.