Save time and summarize this page’s content
Choose your tool to generate a summary of this page:

PhotoRobot Turning Platform 180 and 280 cm - Light Setup

This manual shows where the eight studio lights of the 180 cm and 280 cm Turning Platforms go and how to angle them, with and without the Robotic Arm. Both sizes use the same light set. Installation of the platform itself is described in the Turning Platform User Guide.

Before you start

  • During assembly, make sure the arm has a full range of motion between 0 deg and 90 deg.

1 The Eight Lights at a Glance

# Light Modifier Stand Position and angle
1 Product top light softbox 90 x 120 cm, vertical LS-13B with wall boom clamp behind the camera (with the Robotic Arm: above the camera), as close as possible to the turntable; tilted about 45 deg
2 Product left light softbox 90 x 120 cm, vertical LS-13B front left; tilted about 45 deg toward the platform
3 Product right light softbox 90 x 120 cm, vertical LS-13B front right; tilted about 45 deg toward the platform
4 Lower front light softbox 40 x 120 cm, horizontal LS-3B in the front section, in front of the camera
5 Side left light softbox 40 x 120 cm, horizontal LS-13B left side; tilted about 45 deg toward the platform
6 Side right light softbox 40 x 120 cm, horizontal LS-13B right side; tilted about 45 deg toward the platform
7 Background left light strip softbox 30 x 180 cm, vertical LS-13B 130 mm from the edge of the background, 450 mm from the background; toward the middle of the background
8 Background right light strip softbox 30 x 180 cm, vertical LS-13B as light 7, mirrored

The background is 3,550 mm wide, stands on two LS-13B stands and is 400 mm behind the platform edge. Laser 1 stands on an LS-13B stand at the right side, laser 2 on an LS-13B stand behind the background.

2 Light Plan: Turning Platform 280 cm

Turning Platform 280 cm light plan: eight lights with type, stand and tilt at each light, background 3 550 mm, plus a setup table.
01 Product top · 02 Product left · 03 Product right · 04 Lower front · 05 Side left · 06 Side right · 07 Background left · 08 Background right

3 Light Plan: Turning Platform 180 cm

The 180 cm platform uses the same lights, background and background light positions. Lights 1 to 6 are shown in indicative positions.

Turning Platform 180 cm light plan: eight lights with type, stand and tilt at each light, background 3 550 mm, plus a setup table.
01 Product top · 02 Product left · 03 Product right · 04 Lower front · 05 Side left · 06 Side right · 07 Background left · 08 Background right

4 Front Top Light (1)

The top product light with a 90 x 120 cm softbox in a vertical position is mounted on an LS-13B stand with a wall boom clamp, behind the camera, as close as possible to the turntable, with a light tilt of about 45 deg. During assembly, make sure the arm has a full range of motion between 0 deg and 90 deg.

5 Front Left and Right Lights (2 and 3)

The front left and right lights have 90 x 120 cm softboxes in a vertical position and are mounted on LS-13B stands at a tilt of about 45 deg toward the platform.

6 Lower Front Light (4)

The lower front light has a 40 x 120 cm softbox in a horizontal position and is placed in the front section in front of the camera on an LS-3B stand.

7 Side Left and Right Lights (5 and 6)

The side left and right lights have 40 x 120 cm softboxes in a horizontal position and are mounted on LS-13B stands at a tilt of about 45 deg toward the platform.

8 Background Left and Right Lights (7 and 8)

The background left and right lights have 30 x 180 cm strip softboxes in a vertical position, are mounted on LS-13B stands and shine directly toward the middle of the background. Exact position: 130 mm from the edge of the background and 450 mm from the background.

9 With the Robotic Arm

With the Robotic Arm the eight lights are the same. The top light (1) is mounted on the LS-13B stand with the wall boom clamp above the camera, as close as possible to the turntable, tilted about 45 deg. The camera is on the arm, which stands at the left side of the platform; the side left light (5) moves toward the background.

Turning Platform 280 cm with Robotic Arm light plan: eight lights with type, stand and tilt at each light, background 3 550 mm, plus a setup table.
01 Product top · 02 Product left · 03 Product right · 04 Lower front · 05 Side left · 06 Side right · 07 Background left · 08 Background right
Turning Platform 180 cm with Robotic Arm light plan: eight lights with type, stand and tilt at each light, background 3 550 mm, plus a setup table.
01 Product top · 02 Product left · 03 Product right · 04 Lower front · 05 Side left · 06 Side right · 07 Background left · 08 Background right

10 Equipment

The same for both sizes, with and without the Robotic Arm:

Qty Item
8 lights
3 90 x 120 cm RECTA Exclusive softbox, with speed ring and adapter
2 30 x 180 cm STRIP BOX Exclusive softbox, with speed ring and adapter
3 40 x 120 cm STRIP BOX Exclusive softbox, with speed ring and adapter
1 Master LS-3B stand, max. 85 cm, 2 sections
10 Master LS-13B stand, max. 380 cm, 4 sections
1 wall boom set (counterweight + clamp)
1 wall boom pole with 2 m pin

11 Light Control

Light control: Broncolor Lights Management or the FOMEI manuals, depending on the light set.

PhotoRobot Academy

Learn It in the PhotoRobot Academy

This manual is the reference. The Academy teaches the topic step by step, with exercises and a certificate.

Full curriculum outline